- For use on 8-key single speed freewheels - Tool Type: Freewheel Remover - Compatibility: 16-22T smallest cog (Gray) - Compatibility: 13-14T smallest cog (Silver)
Crank Brothers puts their well-known design aesthetic to the humble tire lever with the Speedier Lever. Can we call a single piece of nylon revolutionary? First off, this thing is tough. It removes and installs wire-beaded DH tires, UST tires, and brand-new road tires easily, without breaking. The genius loop protects your knuckles! It installs tires too, without pinching the tube, just flip it and use the other side. And only one lever is needed to remove even the most recalcitrant tires. Oh Speedier Lever, where have you been all my life?
- Slotted construction for securing Aerolite bladed spokes - Helps prevent spoke twisting while wheel building/truing - Red handle for 0.8-1.0mm spokes - Black handle for 1.0-1.3mm spokes
- Professional wrenches fit internal nipples on many deep section aero rims
$18.99 - $29.99
The Finish Line Absorb-It Mat is the perfect way to keep any work area clean. Designed with special absorption fiber technology, the Absorb-It Mat absorbs and traps chain lubricants, cleaners, degreasers, brake fluid and hydraulic oils. The combination of absorption fibers and a leak-proof poly liner make the Absorb-It Mat perfect accessory when degreasing & lubricating bicycle chains. Use the Absorb-It on a work bench, under an automobile to catch leaking fluids, in a car trunk to prevent stains, in a chemical storage cabinets, or under a trainer to catch perspiration. The Absorb-It Mat comes in two different sizes: Small (48" X 18") and Large (60" X 36"). The 48" x 18" will absorb and trap up to 11L of fluids. The larger 60" x 36" will absorb and trap up to 2.5L of fluid. Both mats can be cut with a scissor to fit in custom areas.
The Easy-Pro Brush Set includes 5 different brushes that make easy work of all bike-cleaning jobs. Use them to remove mud, dirt and road grime from your frame and components. The package comes with a features-and-benefits guide that explains the multiple uses of each brush. Also included is a chain for hanging the brushes when they're not in use.
- Pad/rotor alignment tool, helps set up pad gap on all Hayes brakes
Hayes Pro bleed kits include dual syringes and high quality fittings for precise, repeatable bleeds. D.O.T. Brake Fluid Dual Syringe Pro Bleed Kit - Includes 4oz of high performance Hayes DOT 4 brake fluid - Quick connect fittings and dual syringes for an efficient, precise bleed - Bleed fittings for Hayes DOT 4 brakes - Reusable plastic container with locking lid Venom Mineral Oil Dual Syringe Pro Bleed Kit - Includes 2oz of high performance Hayes Venom mineral oil - Quick connect fittings and dual syringes for an efficient, precise bleed - Bleed fittings for Hayes Venom mineral oil brakes - Reusable plastic container with locking lid
• Lightweight reinforced nylon construction • Smooth edges won't scratch rims or pinch tubes • Storage clip features built-in abrasive surface
The Lezyne EXBBT-CLT Two-Way Tool integrates an external bottom bracket cup and cassette lockring tool into one dual purpose unit. It works perfectly with Lezyne's 32mm CNC Rod (sold separately) or an adjustable wrench. The tool is made of durable, forged, and heat treated steel that is CNC machined for extremely accurate engagement. It is compatible with most external bottom brackets and cassette lockrings.
- Makes the installation of hydraulic disc brake calipers quick and easy - Helps properly align a hydraulic disc brake caliper with the rotor - Ensures even spacing between disc brake pads and rotor - Compatible with all styles of hydraulic disc brakes - Durable stainless steel construction
Origin-8's Wood 8-In-1 Mini Tool features a plethora of tools with an excellent wood grip. It features a 2, 2.5, 3, 4, 5, and 6mm hex keys, Phillips and flat-head screwdrivers, and a T-25 Torx
- Dark nickel plated finish - CNC machined arms - Hex keys: 2/3/4/5/6mm - Flathead and Phillips screwdrivers - T25 Torx
Origin-8's Wood 11-In-1 Mini Tool features a plethora of tools with an excellent wood grip. It features a 2, 2.5, 3, 4, 5, 6 and 8mm hex keys, screwdrivers, T-25 Torx, and a chain tool.
- Shop-quality bottom bracket tool for damage-free installation and removal of Origin8 Revolvr 12-notch x 36mm BB cups - Center post helps to fix and stabilize the tool in to the BB cup - 1/2" drive is compatible with ratchet and torque wrenches - Required for Parts #211565 and #211566 - Compatibility: Shimano HTII 24mm and SRAM GXP 22/24mm - Size: 12-Notch x 36mm - Brand Compatibility: Origin8 BB90/95
Precision CNC machined aluminum tool for the installation and removal of 16-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. - 16 notch 49mm OD cup - Fits FSA MegaEvo and more
The CC-4 is a drop-in style gauge that measures bicycle chain wear. The laser cut CC-4 accurately measures a long section of chain and strategically comes in contact with the chain in three places, quickly and easily taking the guesswork out of knowing when chain replacement is necessary. A worn chain will cause poor shifting as well as accelerate drivetrain wear. The tool works on any 5 to 12-speed derailleur chain (including SRAM AXS) and is designed to accurately indicate when a chain reaches .5% and .75% wear, the points at which most chain manufacturers suggest replacement.
Proper frame preparation is very important. Park Tool's Head Tube Reaming and Facing Set (33.8mm reamer) combines reaming and facing of the head tube to create a perfect fit for most sizes of head cups. The HTR-1B comes with a reamer of 33.9mm for the 1-1/8 inch headset standard. Includes: • 33.9mm reamer (part #754.2), and four different size pilots (29.8mm, 30.0mm, 33.8mm, and 36.8mm) • 690 Facer • Quick-release, quick-adjust feature: bottom portion slides off and on easily without threading SHIS terminology: The HTR-1B as stock will face frames of EC29, EC30, EC34 and EC37. It will ream frames of EC34. Accessories will allow service in other standards.
Precisely machined for a perfect fit, this 8-notch tool removes and installs the lockring that retains front chainrings found on Bosch Gen 2 e-bike motors after the crank arm is removed. - Fits Bosch Active Line (chainrings less than 20 teeth), Performance Line and Performance Line CX models - For lockrings with 50mm outside diameter and 8 notches - Replacement for Bosch 0275009003 tool - Torque wrench compatible 3/8-inch square drive - Constructed of 4140 heat treated steel and plated for long life
A purpose-built wrench designed for compression nuts, nipples, and other fittings found on hydraulic brake systems. The five-sided flare wrench head evenly spreads out the force being applied to the wrench, reducing the risk of damage to fasteners and brake hoses. Features a slim, low-profile design to access low-clearance fittings found on hydraulic levers and calipers. Built-in 3/8" fittings allow for use with a torque wrench to achieve proper torque. - Double-sided wrench features 7mm and 8mm wrench openings - Dimensions: 4" x 0.75" x 0.15" (101mm x 19.5mm x 4.5mm) - Weight: 44g (1.55 oz.) NOTE: When using with a torque wrench, the MWF-3 should be installed at a 90° angle from the beam of the wrench.
This 7mm and 9mm flare wrench is used to open and close compression nuts/fittings on hydraulic systems. The MWF-2 features angled heads for easy access and unique, semi-box openings to reduce the risk of damage to compression fittings.
Park Tool's 8mm and 10mm Metric Flare Wrench is used to safely open and close the compression nut on hydraulic brake calipers and levers. The MWF-1 features angled heads for easy access, and unique, semi-box openings to reduce the risk of damage to the compression nut and brake line.
The BBT-16 removes and installs the self-extracting/one-key release caps on SRAM and RaceFace cranks with a 16mm hex hole. Features investment cast steel construction and an option to use 8mm hex for better leverage.
$0.86 - $5.99
Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs
Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.
Park's Chainring Nut Wrench makes chainring bolt installation and removal easy. It securely holds the slotted nut to prevent spinning when tightening or loosening the bolt. And, it's double-ended to fit most slotted-type nuts, including Campagnolo chainring bolt nuts.
Get those heads sealing like new and reduce compressor energy waste with Park Tool's Head Seal Kit. This kit will help get rid of that hissing sound you've been hearing when it has been too long since servicing your Park Tool INF-1 or INF-2 shop inflator. Kit includes: - 1 #1586 Presta Seal - 1 #1588 Schrader Seal - 2 #1576-2 O-rings for Shuttle-valve - 1 #1682-2 O-ring for INF-1 and INF-2 Head Adaptors
$8.49 - $11.99
Park's professional-quality, precision-sized spoke wrenches are hardened and chrome plated for long service. Wrenches are vinyl coated in one of four colors indicating the size at a glance. You will find these wrenches in virtually every professional bike shop and every shop mechanic's personal tool stash. Make sure you have the sizes you need in your home toolbox and bike bag.
$8.99 - $9.99
Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. This 23mm size fits Shimano 15mm through-axle hubs. Some applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.
Page 1 of 6 Next page